Every maker eventually faces the same problem. One shape done well is satisfying, but six identical shapes done well is a different discipline entirely. A curved chair rail, a set of cabriole legs, a run of bracket feet: once a design calls for repetition, freehand work begins to show its limits. Small variations that go unnoticed on a single piece become glaring when parts sit side by side.
The template is the traditional answer. Chairmakers, coachbuilders and shipwrights have kept patterns for centuries, often hanging them from shop rafters for decades. A good template stores decisions. Once a curve is right, it stays right, and every future piece inherits that accuracy without the maker having to rediscover it.
But a template is only as good as the care put into it. Any flaw in its edge, whether a flat spot, a bump or a slightly wandering line, gets faithfully copied into every part. Making templates well is a craft of its own. It rests on three decisions: what material to use, how to get the shape onto it, and how to refine that edge until it deserves to be reproduced.
Material Selection: Matching Stock to Purpose
MDF is the default for router templates, and for good reason. Its uniform density means there is no grain to tear out or follow, so it cuts, files and sands to a consistent edge in any direction. A half-inch (12mm) sheet gives the bearing of a flush-trim or pattern bit plenty of surface to ride against. Its weaknesses are softness and moisture. Edges dent when dropped, and a damp shop will swell them. A coat of shellac or thin cyanoacrylate glue on the edge hardens it considerably.
Plywood, particularly Baltic birch, is tougher and holds screws far better. That matters when a template needs toggle clamps, fences or stop blocks attached. The tradeoff is the edge. Alternating veneer layers sand at slightly different rates, and lower-grade sheets hide voids that can catch a bearing. Plywood suits jigs and templates intended for heavy, repeated production use.
Hardboard is the classic pattern material for tracing rather than routing. Tempered sheets of 1/8 or 1/4 inch (3–6mm) are thin, inexpensive, rigid enough to hold a curve and easy to store. This is why so many old shops have stacks of it marked with chair parts. Thinner sheets give a bearing too little contact for reliable routing, so hardboard often serves as a master pattern. Thicker routing templates are then made from it as needed.
Acrylic offers something no other material does: transparency. Seeing the workpiece through the template lets you position it around grain figure, knots or existing joinery. It is durable and holds a crisp edge. However, it chips if cut aggressively and melts under friction, so it demands sharp blades, slow feeds and patience at the sanding stage. Polycarbonate is a less brittle alternative where impact resistance matters more than a polished edge.
TakeawayChoose template material by how the template will be used, whether it will be traced, routed or positioned, rather than by what happens to be in the offcut bin. The material sets the ceiling on how accurate and durable the template can be.
Transfer Methods: Getting the Shape onto the Stock
The most reliable way to move a drawing onto template stock is also the simplest. Print or photocopy the pattern at full size and adhere it directly to the material with repositionable spray adhesive. You then cut and shape to the line itself, which eliminates the error that creeps in with every intermediate tracing. Before trusting any printout, measure it. Copiers and printers can distort a pattern by a percent or two, sometimes unevenly between the two axes. A reference line of known length, drawn in both directions on the original, lets you verify scale at a glance.
For symmetrical shapes, make a half template. Draw a centreline on the stock, shape one half carefully, then flip it along that line to trace the other side. This guarantees symmetry in a way that drawing both halves never can, and it halves the amount of fairing required. Chairmakers have used this method on splats and crest rails for generations.
Copying from an existing piece introduces a subtler problem: offset. A pencil traced around an edge sits a line's width outside the true shape, and that error accumulates across copies. Use a marking knife or a 0.5mm mechanical pencil held consistently upright. For edges that resist direct tracing, a washer rolled along the edge with a pencil in its hole draws a constant offset line. Rolling the same washer back along that line later removes the offset precisely.
Where no drawing exists, curves can be generated directly. A thin, straight-grained batten bent between nails or blocks produces a fair curve naturally, because wood resists forming kinks. A trammel, or a simple strip of wood with a pivot and a pencil hole, draws true arcs of any radius. These methods mean the template captures an intention rather than an approximation, which is the whole point of making one.
TakeawayEvery transfer step is a chance for error to enter. The best method is usually the one with the fewest intermediate copies between the design and the template edge.
Template Refinement: Earning the Right to Be Copied
Start by cutting just outside the line on a bandsaw, scroll saw or jigsaw, leaving roughly a millimetre of waste. The saw's job is removal, not accuracy. The real work begins once the rough shape is free, because a router bearing or tracing pencil will follow every irregularity on that edge with complete fidelity.
Convex curves respond well to a spokeshave, a block plane or a long sanding block. Length matters here. A long tool bridges small hollows and takes down the high spots rather than riding over them. Concave curves need tools with a tighter radius than the curve itself: an oscillating spindle sander, a sanding drum in a drill press, half-round files, or sandpaper wrapped around a dowel. Work to the line slowly, with the template clamped at a comfortable height under good raking light.
Judge fairness with more than your eyes. Sight along the edge from one end, the way a boatbuilder checks a plank. Run your fingertips along it with your eyes closed, since touch picks up small irregularities that sight misses. Hold a fairing batten against curves and look for light leaking through. Finally, check that the edge is square to the face. A bevelled edge shifts where the bearing makes contact and quietly changes the cut.
Keep the router's own limit in mind: no bearing-guided bit can cut an inside curve tighter than its own radius, so design inside curves accordingly. Before production, rout a test piece in scrap and inspect it critically. Then label the finished template with the project, date, grain direction, reference marks and the bit it was designed for. A template outlasts memory, and the information written on it is part of its accuracy.
TakeawayA template does not average out its mistakes; it multiplies them. Time spent fairing one edge is time saved on every part that edge will ever produce.
Template making rewards a particular kind of patience: investing heavily in one object so that many others come easily. It shifts effort away from the production run and into the preparation, which is where careful makers have always preferred it to live.
A useful framework is to treat each template as a finished piece in its own right. Choose material to suit its job. Transfer shapes with as few intermediate steps as possible. Refine the edge until it passes the eye, the fingertip and the test cut. Then label and store it as if someone else will rely on it, because in a few years that someone will be you.
Over time, a wall of good templates becomes a record of solved problems, ready whenever the work calls for them again.